Geleceği İnşa Ediyoruz
Elektrik Makinaları Sanayi
Oil fuel pumps NK and NKV types
Oil fuel pumps NK and NKV centrifugal type can be used for transferring and piping oil, oil products, dry hydrocarbon gases and other liquids which have similar physicochemical features and the same corrosive impact to the pump component material.
Oil fuel pumps NPS type
Oil fuel pumps NPS type can be assigned for transferring and piping oil, oil products, dry hydrocarbon gases and other liquids, which have similar physicochemical features and the same corrosive impact to the pump component material; temperature from minus 80 °C plus +200 °C. The allowed level of nonabrasive solid particles in the pumped fluid is not more than 0,2% w/w; the allowed particle size is not more than 0,2 mm
Centrifugal pumps CNSSh type
Centrifugal pumps of the CNSSh type are designed for pumping water and other neutral liquids similar to water in density and viscosity, with a pH of 5.5 ... 8.5, with temperature of up to 70 ° C, with a total content of sulfates and chlorides up to 20 g / l, mass concentration of solids up to 1.5% and particle size up to 1 mm.
Centrifugal pumps CNSn type
Pumps of the CNSn types are intended for pumping watercut gas-saturated and commercial oil in the systems of infield collection, preparation and transportation of oil without hydrogen sulfide.
Metering pumps ND type
Metering plunger pumps and units can be assigned for voluminous pressure metering of neutral and aggressive liquids, emulsions and slurry oils which have kinematic viscosity from 8,5x10-7 to 8x10-4 m²/s (from 0,0085 to 8 St); temperature from 258K to 473K (from minus 15°C to plus 200°C and more); nonabrasive solid phase concentration not more 10% in the mass with maximum particle density up to 2000 kg/m³; particle size of nonabrasive solid phase not more than 1% from internal diameter of inlet nozzle.
NDR-2M type metering diaphragm pumps
Designed for pumping liquids and suspensions, including toxic and aggressive ones. The presence of abrasive in the pumped liquid is allowed.
Three-plunger crank pumping T, PT type
The T and PT three-plunger crank units and pumps are designed to pump both neutral liquids and aggressive liquids, which are neutral to the materials of the hydraulic portion, with the kinematic viscosity of not more than 800 mm2/sec (8 St) at a temperature depending on the make of 243 K to 473 K (minus 30°С to plus 200°С). The allowed level of nonabrasive solid particles in the pumped fluid is not more than 0.2 % w/w; the allowed particle size is not more than 0.2 mm.
Horizontal double-entry pumps of D type
Single-stage horizontal centrifugal pumps with double-sided semi-volute supply of liquid to the impeller and with volute discharge (type Д). Intended for pumping of water and liquids with similar properties in terms of reactivity, with temperature up to 85 °С, and viscosity up to 36 cSt. The maximum allowed mass content of solid particles is below plus 0.05 %, the grain size is under 0.2 mm
CN type pumps
Centrifugal horizontal of spiral type with double-entry impellers. The pumps are to pump water and liquids of similar with water characteristics of viscosity and chemical activity, temperature up to 100°C, with maximal concentration of solid particles of 0,05% and of size of 0,2mm.
PE type pumps
Centrifugal horizontal single-hull sectional with one- sideddisposition of wheels. The pumps are for pumping of feed water with pH value of 7-9,2, temperature not higher than 438K (165°C), not containing solid particles. The Pumps are used for feeding with water of fixed steam boilers with absolute steam pressure of 4,0; 5,3; 6,3 MPa (40, 53, 63 kgs/cm2).
SE Type Pumps
Designed for pumping water with temperatures below 185 °С, containing particulate matter under 0.2 mm at concentrations below 5 mg/L. Are used for pumping water in heat supply networks.
Water ring vacuum pumps VVN type
Water ring vacuum pumps VVN type are designed (depending on the material of the flow path) for suction of air, inert or aggressive gases, insoluble in water, in order to create or maintain a vacuum
Radial piston pump NR 2-1250
The radial piston pump NR 2-1250 is designed to supply working fluid to the hydraulic system of the walking mechanism of walking excavators and other powerful hydroficated machines, where an unregulated flow rate with a pressure of up to 20 MPa is required.
Axial pump type PG
PG pumps are horizontal cantilever pumps with axial fluid supply to the impeller. The main branch of application of pumps of the PG type is the assembly of pumping mobile stations of the SNP(E) type. Pumping stations are designed for irrigation and drainage works, for supplying water from various reservoirs to an open irrigation network with a lifting height of 10 meters.
Submersible borehole pumps type ETsV
The ETsV centrifugal downhole electric pump unit for water is designed for urban, industrial and agricultural water supply, pressure increase, irrigation, formation water pumping, water drawdown, etc
Cantilever pumps type K
Industrial cantilever pumps of types K designed for stationary operation for pumping water (except sea water) with pH 6…9, temperature 0…+85°С and other liquids similar to pure water in density, viscosity and chemical activity, containing solid inclusions of size up to 0.2 mm.
